Smart Tool Overview
What You'll Learn
- What smart tools are and why wireless data capture matters for diagnostic accuracy
- Which measurement categories measureQuick supports (refrigerant, airflow, electrical, combustion, evacuation, IAQ)
- How smart tools connect to the app (Direct BLE, App-to-App, QR Code)
- Which manufacturers and tool models are compatible
- How measureQuick classifies tools into device groups
- Where to find the Tools screen in the app and what it shows
- How to explore the Tools screen using Demo Mode without connected hardware
What You'll Need
- Device: iPhone (iOS 15+), iPad, or Android phone/tablet (Android 10+)
- Account: A measureQuick account with the app installed (see App Installation)
- Smart tools: Not required for this overview. You can explore the Tools screen in Demo Mode.
- Time: 10-15 minutes to read
Why Wireless Data Capture Matters
Manual data entry introduces errors. A technician reading an analog gauge, rounding to the nearest PSI, and typing that number into a form can easily be off by 5-10 PSI. That margin changes superheat and subcooling calculations enough to produce a false pass or false fail.
Smart tools eliminate that gap. When a wireless pressure probe streams data directly to the app, the reading is exact and timestamped. measureQuick receives the raw value, applies the correct refrigerant properties, and calculates superheat, subcooling, and system performance in real time. No rounding, no transcription errors, no delays.
This also means your test records are defensible. Every measurement has a timestamp, a source instrument, and a data trail. When a customer or warranty provider asks how you arrived at a diagnosis, the answer is in the test record.
measureQuick supports 37 compatible smart tools from 17 manufacturers. The rest of this article covers what those tools are, what they measure, and how they connect.
How Smart Tools Connect
Smart tools use one of three connection methods to get data into measureQuick.
Direct Connect (BLE)
Most smart tools (30 of 37) use Bluetooth Low Energy to pair directly with the measureQuick app. You turn on the tool, open the app, and the tool appears in the connection list. Data streams in real time.
BLE range varies by tool. Most work within 30-100 feet. Yellow Jacket YJACK probes have a 400-foot line-of-sight range. Fieldpiece SMAN manifolds reach up to 1,000 feet.
measureQuick can maintain 15+ simultaneous BLE connections. You can have pressure probes, temperature clamps, a psychrometer, and a clamp meter all streaming data at the same time.
App-to-App
Three tools connect through their manufacturer's app rather than directly to measureQuick:
| Tool | Manufacturer App | What It Measures |
|---|---|---|
| TEC TrueFlow Grid | TEC TrueFlow App | Airflow (CFM) |
| AccuTools BluVac | BluVac App | Vacuum level |
| iManifold / iConnect | iManifold App | Pressure, temperature |
For App-to-App tools, the manufacturer's app handles the Bluetooth connection. measureQuick reads the data from that app. Both apps must be open on your device.
QR Code
One tool uses QR code transfer:
- Bacharach Fyrite Insight / InTech - You run the combustion test on the analyzer, then scan a QR code on the Fyrite's screen to import results into measureQuick.
This tool has been sunset (discontinued from active support). It still works if you own one, but Sauermann is the current recommended combustion analyzer.
Compatible Tools by Measurement Category
measureQuick organizes smart tools into device groups based on what they measure. Below is every compatible tool, grouped by category.
Refrigerant Pressure & Temperature (Manifold Gauges)
These tools measure high-side and low-side refrigerant pressures and line temperatures. measureQuick uses this data to calculate superheat, subcooling, and charge status.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| Fieldpiece SMAN (SM380V, SM382V, SM480V, SM482V) | Fieldpiece | Direct BLE | Active | 3-port and 4-port models. 1,000 ft BLE range. Built-in vacuum gauge (50-9,999 microns). SM482V recommended as best-in-class. |
| Fieldpiece JobLink Probes (JL3PR) | Fieldpiece | Direct BLE | Active | Wireless pressure probes. Part of the JobLink ecosystem. |
| Testo 550 / 557 Digital Manifolds | Testo | Direct BLE | Active | 60+ refrigerant profiles. Tightness test function. |
| Testo Smart Probes (549i) | Testo | Direct BLE | Active | High-pressure gauge. Compact wireless design. |
| NAVAC NX1 / NX4 Digital Manifolds | NAVAC | Direct BLE | Active | 100+ refrigerants including A2L. 4 operating modes (manifold, leak test, evacuation, decay test). |
| NAVAC Smart Probes | NAVAC | Direct BLE | Active | Wireless temperature clamps and pressure probes. |
| Yellow Jacket TITANMAX / YJACK PRESS | Yellow Jacket | Direct BLE | Active | 400 ft range. YJACK PRESS is a standalone wireless pressure probe. |
| UEi HUB6 / HUB8 (WPP1 probes) | UEi | Direct BLE | Active | Wireless pressure probes as part of the HUB system. |
| JB Industries CLIMATE CLASS | JB | Direct BLE | Active | 4-valve forged aluminum manifold. Wireless temp clamps and psychrometers included. |
| Seitron Be Cool Evo M4S | Seitron | Direct BLE | Active | 4-way manifold. 150+ refrigerants. 72+ hour battery. Bluetooth 5.0. |
| Parker Sporlan SMART Probes | Parker Sporlan | Direct BLE | Active | Wireless pressure and temperature probes. |
| iManifold / iConnect | iManifold | App-to-App | Active | Connects through iManifold app. |
Temperature Probes
Temperature clamps and probes measure line temperatures, supply/return air, and ambient conditions. Most manufacturers bundle temperature probes with their pressure systems.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| Fieldpiece JobLink Probes (JL3PC) | Fieldpiece | Direct BLE | Active | Pipe clamp temperature probe. |
| Testo Smart Probes (115i) | Testo | Direct BLE | Active | Pipe-clamp thermometer. |
| NAVAC Smart Probes | NAVAC | Direct BLE | Active | Temp clamps with built-in display. Range: -40 to 257F. |
| Yellow Jacket YJACK TEMP | Yellow Jacket | Direct BLE | Active | 400 ft range. |
| UEi HUB6 / HUB8 (WPC2 clamps) | UEi | Direct BLE | Active | Pipe clamp probes. Accuracy: +/-0.5F. |
| JB Industries CLIMATE CLASS | JB | Direct BLE | Active | Color-coded over-molded clamps. |
| Seitron Be Cool Evo M4S | Seitron | Direct BLE | Active | 3x K-type thermocouple inputs. |
Humidity / Psychrometer
Psychrometers measure wet bulb and dry bulb temperatures plus relative humidity. measureQuick uses this data for airflow calculations and indoor air quality assessment.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| Fieldpiece JobLink Probes (JL3RH) | Fieldpiece | Direct BLE | Active | Wireless psychrometer. |
| Testo Smart Probes (605i) | Testo | Direct BLE | Active | Thermohygrometer. |
| NAVAC Smart Probes | NAVAC | Direct BLE | Active | Humidity-capable probes. |
| Yellow Jacket YJACK DEW | Yellow Jacket | Direct BLE | Active | Psychrometer probe. |
| UEi HUB6 / HUB8 (WHP1) | UEi | Direct BLE | Active | Wireless hygrometers. |
| JB Industries CLIMATE CLASS | JB | Direct BLE | Active | Standalone psychrometer. |
| CPS EasyHood & Airflow Meter | CPS | Direct BLE | Active | Includes RH measurement (0-85% RH). |
| Testo 420 Capture Hood | Testo | Direct BLE | Active | Includes humidity measurement. |
Static Pressure & Differential Pressure
Static pressure tools measure the pressure drop across ductwork components. measureQuick uses these readings to evaluate airflow restriction and duct system performance.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| Fieldpiece JobLink Probes (JL3KM2) | Fieldpiece | Direct BLE | Active | Wireless manometer for static pressure. |
| CPS Static Pressure Meter | CPS | Direct BLE | Active | Dual port. Range: +/-75 inWC. Resolution: 0.004 inWC. 500+ hour battery. |
| UEi DPM Wireless Manometer | UEi | Direct BLE | Active | Range: +/-80 inWC. Dual port. Magnetic mount. |
| UEi SPMKIT Static Pressure Kit | UEi | Direct BLE | Active | Kit includes 2 manometers, 2 static pressure probes, fittings, and tubing. |
| Testo Smart Probes | Testo | Direct BLE | Active | Static pressure measurement capability. |
| Yellow Jacket YJACK MANO | Yellow Jacket | Direct BLE | Active | Manometer probe. 400 ft range. |
| TEC DG-1000 | TEC | Direct BLE | Active | Dual-channel digital gauge. Range: +/-10 inWC. 0.1 Pa resolution. |
| TEC TrueFlow Grid | TEC | App-to-App | Active | Also measures static pressure as part of airflow calculation. |
| Testo 420 Capture Hood | Testo | Direct BLE | Active | Includes detachable manometer. |
| Sauermann Combustion Analyzers | Sauermann | Direct BLE | Active | Draft/pressure measurement: -80 to +80 inH2O. |
Airflow Measurement
Airflow tools measure CFM at registers or through the air handler. measureQuick uses airflow data to evaluate system performance and calculate delivered capacity.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| TEC TrueFlow Grid | TEC | App-to-App | Active | Replaces the filter to measure total system airflow. 8 adapter sizes (14x20 through 25x25). Range: 300-2,500 CFM. Connects through TEC TrueFlow app. |
| TEC DG-1000 | TEC | Direct BLE | Active | Dual-channel digital gauge used with TrueFlow Grid or for standalone pressure-based airflow. |
| CPS EasyHood & Airflow Meter | CPS | Direct BLE | Active | Capture hood. 12x12 base expandable to 24x24. Range: 35-1,200 CFM (7-100 CFM low flow). |
| Testo 420 Capture Hood | Testo | Direct BLE | Active | 24x24 hood. Range: 25-2,300 CFM. Integrated flow straightener. Under 6.4 lbs. |
Electrical Measurement
Clamp meters and multimeters measure voltage, amperage, power factor, and wattage. measureQuick uses electrical data to calculate system efficiency and verify equipment operation.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| UEi DL599 Power Clamp Meter | UEi | Direct BLE | Active | True RMS. 600A. Power factor, kW, kVA, kVAr. 3-phase rotation. CAT IV 600V. |
| UEi HAC High Accuracy Clamp Meter | UEi | Direct BLE | Active | True RMS. 200A. High accuracy (+/-1.5%). CAT IV 600V. |
| CPS VOLT-100 Clamp Power Meter | CPS | Direct BLE | Active | True RMS. 600A. THD measurement. Rechargeable Li-ion. CAT IV 600V. |
| Redfish iDVM550 Power Clamp Meter | Redfish | Direct BLE | Active | True RMS. Single-phase power and PF. CAT III 600V. |
| Redfish iDVM510 Digital Multimeter | Redfish | Direct BLE | Active | True RMS. IP54 rated. 2MB on-board logging. CAT IV 600V. |
| Fieldpiece Multimeter | Fieldpiece | Direct BLE | Active | Amps, volts, capacitance, frequency, ohms, power, temperature. |
| Yellow Jacket YJACK AMP | Yellow Jacket | Direct BLE | Active | Limitation: YJACK AMP will not pull amps into measureQuick. It connects but does not transfer amperage data. |
Note on YJACK AMP: While this probe pairs with measureQuick via Bluetooth, it does not transmit amperage readings into the app. If you need wireless amp data in measureQuick, use one of the other clamp meters listed above.
Combustion Analysis
Combustion analyzers measure O2, CO, CO2, flue temperature, and stack draft. measureQuick uses this data for gas furnace and boiler diagnostics.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| Sauermann Combustion Analyzers | Sauermann | Direct BLE | Active | O2 (0-25%), CO (0-8,000 ppm), flue temp (-4 to 2,282F), draft (-80 to +80 inH2O). Optional NOx. Field-replaceable sensors. |
| BluFlame Combustion Analyzer | Accutools | Direct BLE | Sunset | Touchscreen. MSM field-replaceable sensors. No longer in active support. |
| Bacharach Fyrite Insight / InTech | Bacharach | QR Code | Sunset | QR code data transfer only. B-Smart pre-calibrated sensors. No longer in active support. |
Sauermann is the only actively supported combustion analyzer for measureQuick.
Evacuation & Vacuum
Vacuum gauges monitor evacuation progress in microns. Scales measure refrigerant weight during charging.
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| AccuTools BluVac Gauges | Accutools | App-to-App | Active | Range: 0-25,000 microns. 0.1 micron resolution. Connects through BluVac app. 300-hour battery. |
| CPS Wireless Scale | CPS | Direct BLE | Active | 220 lb capacity. NIST calibrated. 150 ft range. Tank Tracker system. |
| Seitron Be Cool Evo M4S | Seitron | Direct BLE | Active | Built-in evacuation mode with vacuum measurement. |
| Fieldpiece Wireless Scale | Fieldpiece | Direct BLE | Sunset | 110 lb capacity. No longer in active support. |
| NAVAC Vacuum Pumps | NAVAC | N/A | Active | Cordless vacuum pumps. Not a data connection to measureQuick; used alongside manifold gauges that do connect. |
Note on YJACK VAC: The Yellow Jacket YJACK VAC vacuum probe does not connect to measureQuick. Use BluVac or a manifold with built-in vacuum measurement instead.
Indoor Air Quality
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| HAVEN Central Air Monitor | HAVEN | WiFi | Active | Measures PM2.5, tVOCs, temperature, and humidity. Installs in the return duct. WiFi connected (not BLE). Can control up to 2 pieces of equipment via R&G terminals. |
| UEi Personal CO Meter | UEi | Direct BLE | Active | Ambient CO monitoring. Range: 1-999 ppm. Alarm at 35 ppm. Belt clip design for personal safety. |
Printing
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| mQ Printer | mQ | Direct BLE | Active | Thermal printer for on-site test reports. Works with all project types (cooling, heating, heat pump, combustion, evacuation, electrical). Includes GPS coordinates and timestamps. |
Specialty
| Tool | Manufacturer | Connection | Status | Notes |
|---|---|---|---|---|
| Accutools TXV Charging Solution | Accutools | N/A | Active | Wraps around the condenser to recirculate discharge air, simulating higher outdoor temps. Enables charging in 35-70F conditions. Not a data connection; a physical accessory used during charging. |
Summary: 17 Manufacturers at a Glance
| Manufacturer | Tool Count | Primary Categories |
|---|---|---|
| Fieldpiece | 4 | Manifolds, probes (pressure, temp, humidity, static), multimeter, scale (sunset) |
| UEi | 5 | HUB system, clamp meters, manometers, static pressure kit, CO meter |
| Testo | 3 | Digital manifolds, smart probes (549i, 115i, 605i), capture hood |
| CPS | 4 | Static pressure meter, clamp meter, wireless scale, airflow meter |
| NAVAC | 3 | Digital manifolds, smart probes, vacuum pumps |
| Yellow Jacket | 1 | TITANMAX manifold + YJACK probe family (pressure, temp, humidity, static, manometer) |
| TEC | 3 | TrueFlow Grid, DG-1000, Digital Pressure Gauge |
| Accutools | 3 | BluVac gauge, TXV charging solution, BluFlame (sunset) |
| JB Industries | 1 | CLIMATE CLASS system (manifold, temp clamps, psychrometers) |
| Seitron | 1 | Be Cool Evo M4S 4-way manifold |
| Parker Sporlan | 1 | SMART Probes (pressure, temperature) |
| Redfish | 2 | iDVM550 clamp meter, iDVM510 multimeter |
| Sauermann | 1 | Combustion analyzers |
| Bacharach | 1 | Fyrite combustion (sunset, QR code) |
| iManifold | 1 | iManifold / iConnect (App-to-App pressure, temperature) |
| HAVEN | 1 | Central Air Monitor (WiFi IAQ) |
| mQ | 1 | Thermal printer |
Connection Type Summary
| Connection Type | Count | How It Works |
|---|---|---|
| Direct BLE | 30 | Tool pairs directly with measureQuick via Bluetooth Low Energy. Real-time data streaming. |
| App-to-App | 3 | Tool connects to manufacturer's app. measureQuick reads data from that app. Both apps run simultaneously. |
| QR Code | 1 | Scan a QR code on the tool's screen to import results. Bacharach Fyrite only (sunset). |
| N/A | 3 | Physical accessories or WiFi devices that do not stream data via Bluetooth (HAVEN, NAVAC pumps, Accutools TXV). |
The Tools Screen in measureQuick
The Tools screen shows all connected and available smart tools. To access it:
- Open the measureQuick app.
- Tap Tools from the home screen or bottom navigation.
The Tools screen displays:
- Connected tools with live status indicators (green = streaming data, gray = disconnected)
- Battery levels for connected instruments
- Signal strength for each Bluetooth connection
- Measurement values updating in real time as tools stream data
When you start a test, measureQuick automatically pulls data from all connected tools into the appropriate measurement fields. You do not need to manually assign readings.
Exploring Tools in Demo Mode
If you do not have smart tools yet, you can see what the Tools screen looks like using Demo Mode.
- Tap Settings (gear icon).
- Tap Advanced Settings.
- Toggle Demo Mode to ON.
Demo Mode simulates connected instruments and live data streams. You can navigate the Tools screen, see how different tool types appear, and understand the interface before purchasing hardware.
Turn Demo Mode off before running real diagnostic tests.
Video Walkthrough
These videos cover smart tool connections and pairing:
YouTube: (26,488 views, 13 min). Detailed walkthrough of pairing Fieldpiece JobLink probes and SMAN manifolds
YouTube: (12 min). Step-by-step Fieldpiece probe addition covering smart tools, static pressure, and probe placement
YouTube: (19,776 views, 6 min). Testo digital manifold setup and live data streaming
YouTube: (8,577 views, 7 min). Electrical meter Bluetooth pairing and data transfer
YouTube: (16,543 views, 5 min). JobLink wireless system overview and pairing
YouTube: (12,714 views, 4 min). Static pressure tool pairing and setup
YouTube: (2 min). SMAN manifold Bluetooth integration overview
YouTube: (66,533 views, 72 min). Full platform overview including tool connections and live diagnostics
Tips & Common Issues
Not all tools from a manufacturer are compatible
Just because a manufacturer has one compatible tool does not mean all their products work with measureQuick. Check the tables above or the Compatible Tools page at measurequick.com before purchasing. Two specific examples: YJACK VAC (vacuum) and YJACK AMP (amperage) do not transfer their primary measurements into the app.
App-to-App tools require both apps open
TrueFlow Grid, BluVac, and iManifold connect through their manufacturer's app first. If you close the manufacturer's app, the data stops flowing into measureQuick. Keep both apps running in the foreground during testing.
Bluetooth range varies significantly
A CPS Static Pressure Meter reaches about 100 feet. A Fieldpiece SMAN reaches 1,000 feet. Yellow Jacket YJACK probes reach 400 feet. Walls, metal ductwork, and equipment cabinets reduce effective range. If you lose connection, move your phone closer to the tool or remove obstructions.
measureQuick manages Bluetooth connections to save battery
The app connects and disconnects from certain tools automatically to preserve battery life on both your phone and the tools. For example, during a gas furnace workflow, measureQuick connects to the combustion analyzer only when the combustion step is activated, then disconnects when that step completes. You may see brief connect/disconnect activity in the Probe Manager; this is normal behavior.
Sunset tools still function but are not updated
BluFlame, Bacharach Fyrite, and Fieldpiece Wireless Scale are marked "Sunset." They still work with measureQuick if you own them, but they no longer receive firmware or compatibility updates. Plan to replace sunset tools when they reach end of life.
More connected probes means better diagnostics
measureQuick requires a minimum of 9 physical probe channels for cooling/heating Vitals scoring and 7 for gas furnace Vitals. Connecting more probes gives the app more data points to work with, which produces more accurate diagnostics and a more complete test record.
Reference Material
measureQuick Compatible Tools
measureQuick Compatible Tools - Page 1
measureQuick Compatible Tools - Page 2
Download: Tests and Probes Quick Reference (PDF)
Download: measureQuick Introduction & Terminology (PDF)
Related Articles
Prerequisites:
Follow-up articles:
- Bluetooth Pairing Basics
- Fieldpiece Probe Pairing
- TrueFlow Grid Setup
- Probe Manager
- Bluetooth Troubleshooting
- Tool Selection Guide
Need Help?
Contact measureQuick support: support@measurequick.com
Related Articles
Smart Tool Selection Guide
What You'll Learn How to choose the right smart tool set for your team based on the work you do Which tools are required for each workflow type: A/C service, heat pump, gas furnace, and full commissioning Budget tiers from entry-level to premium, ...Tool Tracker V3: GPS Tool Location
What You'll Learn How to locate tools on a map using their last-known GPS position How to view tool details including make, model, serial number, last user, and last-seen timestamp How location tracking works under the hood and what determines ...Bluetooth Pairing Basics
What You'll Learn How Bluetooth Low Energy (BLE) works with measureQuick and why it differs from classic Bluetooth The three connection types measureQuick supports: Direct Connect, App-to-App, and QR Code How to pair a BLE smart tool from inside the ...Probe Manager
What You'll Learn What the Probe Manager screen displays and how to navigate it How to read connection status, signal strength, and battery level for each tool How channel mapping works: which probe feeds which measurement slot How to reassign ...Bluetooth Troubleshooting
What You'll Learn How to diagnose and fix the most common Bluetooth connectivity failures in measureQuick The differences between iOS and Android BLE behavior that cause connection problems How to clear your BLE cache and reset tool pairing lists How ...